Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Goltizuru Mazuzahn
Country: Uganda
Language: English (Spanish)
Genre: Video
Published (Last): 20 December 2015
Pages: 360
PDF File Size: 2.29 Mb
ePub File Size: 18.21 Mb
ISBN: 911-5-65351-664-2
Downloads: 24419
Price: Free* [*Free Regsitration Required]
Uploader: Zulubei

See page 9 for more details on input configuration. During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping. V10000 amplifier is designed to mount into a standard 19″ rack. Um ddas Risiko amercan elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. These fans are used to cool the internal parts of the amplifier. Low Cut Frequency Selector When the Low Cut Filter is activated, dip switches 2 channel 1 and 3 channel 2 will control the frequency roll-off.

No hay piezas adentro que el usario puede reparar. Be sure not to operate your amplifier below the minimum load ratings to reduce the risk of overheating problems. Connections are made to Channels 1 and 2 output’s for stereo mode or across the red terminals of Channels 1 and 2 for Mono Xmerican Mode.

VLP1000 power amplifier

If this line good, check the internal speaker connections and components. No user serviceable parts inside. Please read and understand this manual completely before attempting to amercian your new amplifier. Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into Diagram 8 the red terminal.

Connect your speakers to the outputs on the rear of the amplifier. Under americqn clipping activity lower the channel one gain control to reduce there details on input configuration. Amplifiers are shipped in stereo mode.


Refer all servicing to qualified service personnel. Typical speaker output using bare wire. Connect an input signal to channel one. Cooling Fan Dual speed cooling fans.

Short Circuit Protection can usually be traced back to the signal output line i. During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible.

Turn your amp on. Every Vplus series amplifier has been thoroughly tested V and has been shipped in perfect operating condition. This will reduce the use of “Y” cables.

Objects have fallen, or liquid has been spilled into the unit.

Use the channel one gain to regulate your amplifier output. If your speaker lines americaan, the amplifier automatically detects this problem and discontinues operation for that channel.

Each channel operates independently of each other allowing each channel to have different filter settings. Ground Lift Switch This switch is used to disconnect the internal ground signal from the amplifier chassis ground. During excessive clipping the limiter will reduce the audio signal enough to minimize the amount of clipping. Insert the bare wire into the hole that was reveled by unscrewing maerican binding post cap.

Be sure not to raise the volume to the clip level, however an intermittent clip signal is acceptable. Connect your inputs into channels one and two of the amplifier. The front panel provides four holes used to screw the unit into a rack. The lightning flash with an arrow triangular symbol is intended to alert the user to the presence of non insulated americqn voltage” within the products enclosure, and may be of sufficient magnitude to constitute a risk of electric shock.


V Power Amplifier by American Audio Valuation Report by

Use your front gain controls to regulate the output volume. These amplifiers are designed to provide a big impact in sound reproduction. For cable runs shorter than 20ft. The power-supply cord or the plug has been damaged. Check the line from the output terminal of the amplifier to the speaker.

Service Hours are Monday through Friday 9: Channel 2 Frequency Adjustment. This fans are used to cool the internal parts of the amplifier when in use. Clipping should be kept to a reasonable minimum. The fixture does not appear to operate normally or exhibits a marked change in performance. Below rated output, 8 ohms dB, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: Never aydio the fan grills in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail.

Carefully check the smerican carton for damage that may have occurred during shipping.


Except for an occasional flash, keep the “CLIP ” indicator dark to avoid overheating the amplifier channel. Antes de usar amerocan amplificador, lea mas advertencias en la guia de operacion.

Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack. If the breaker continues to pop, stop using the amplifier and contact customer service. The exclamation point triangular symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the user manual accompanying the amplifier.