ASTM A463 PDF

ASTM A – Designation: A /A M – 02a Standard Speci?cation for Steel Sheet, Aluminum-. Find the most up-to-date version of ASTM A at Engineering ASTM A/AM: Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process.

Author: Daijar Meztikora
Country: Slovenia
Language: English (Spanish)
Genre: Relationship
Published (Last): 5 September 2007
Pages: 319
PDF File Size: 18.65 Mb
ePub File Size: 16.20 Mb
ISBN: 179-3-22061-992-4
Downloads: 71155
Price: Free* [*Free Regsitration Required]
Uploader: Voodoonris

B Weight [mass] to thickness conversions are reliable to only two signi? Values in inch-pound and SI units are not necessarily equivalent.

Current edition approved October 10, Within the text, SI units are shown in brackets. H Shall be furnished as a stabilized steel. When the amount of vanadium, titanium, or columbium is less than 0. Individual reprints single or multiple copies of this standard may be obtained z463 contacting ASTM at the above address or at phonefaxor service astm. We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding error.

Continuing dialogue between users and producers will have to be maintained to assist awtm the transition to the new designation system. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability asttm regulatory limitations prior to use.

Values outside of these ranges are to be expected. The following, as required, shall be used to adequately describe the product required.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Astn yield strength tends to increase and some of the formability values tend to decrease as the sheet thickness decreases. This specification covers aluminum-coated steel sheet in coils and cut lengths available with two types of aluminum coating applied by the hot-dip process, with several coating asym. E For carbon levels less than or equal to 0.

  HCPL 4506 PDF

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. These notes and footnotes excluding those in tables and?

Those who use these documents must determine which speci?

Data sheets for overmetals, plastics, ceramics, and composites. These mechanical property values are nonmandatory. These notes and footnotes excluding those in tables and figures shall not be considered as requirements of the standard.

These factors 3 include: Please contact us at webmaster matweb. Questions or comments about MatWeb? This abstract is a brief summary of the referenced standard. The relationship between the standards may only be approximate; therefore, the respective documents should be consulted for actual requirements.

Click here to view all the property values for this datasheet as they were originally entered into MatWeb. E No typical mechanical properties have been established. The typical mechanical properties included in the new designation system are those indicated by the tension test. Property Data This page displays only the text of a material data sheet. Login to see your most recently viewed materials here.

Inch-pound to SI conversions are reliable to?

ASTM A463 Grade FSS-439

Because of the many variables and changing conditions that are characteristic of continuous hot-dip coating lines, the weight [mass] of coating is not always evenly divided between the two surfaces of a sheet, nor a46 the coating evenly distributed from edge to edge. Some of the reasons for this limited relationship are the following: The former designations also did not re?

They are solely to provide the purchaser with as much information as possible to make an informed decision on the steel to be speci? MatWeb is intended for personal, non-commercial use. Historical Version s – view previous versions of standard. 4a63

  DESIGN AND CHARACTERIZATION OF PARALLEL PREFIX ADDERS USING FPGAS PDF

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard has been approved for use by agencies of atsm Department of Defense.

ASTM A Aluminum-Coated Steel, Type I, Drawing Quality

Each system shall be used independently of the other. Link to Active This link will always route to the current Active version of the standard. The minimum requirements only apply to the microalloy elements selected for strengthening of the steel.

Each system shall be used independently of the other. B No minimum means that there are no established minimum requirements for triple- and single-spot tests, but aluminum coating shall be present.

This is not considered to be a fault of the steel but is rather a function of the induced cold-work. Please read our License Agreement regarding materials asm and our Privacy Policy. They are intended solely to provide the purchaser with as much information as possible to make an informed decision on the steel to be speci? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Structural steel and high strength low alloy steel shall conform to the mechanical property requirements. Atm As there is no discontinuous yield curve, the yield strength should be taken as the stress at 0.